|
<< Click to Display Table of Contents > Pin Assignment |
  
|
|
<< Click to Display Table of Contents > Pin Assignment |
|
Port |
USC-1 / USC-2 / USC-3 |
RTC4 |
|---|---|---|
Analog A |
37-pin connector DAC_A → pin 10 |
9-pin SUB-D laser connector (VB3) Analog OUT1 → pin 4, for jumper settings see RTC manual. |
Analog B |
37-pin connector DAC_B → pin 29 |
9-pin SUB-D laser connector (VB3) Analog OUT2 → pin 2, for jumper settings see RTC manual. |
8 Bit Output |
37-pin connector LP 0 → pin 19 LP 1 → pin 37 LP 2 → pin 18 LP 3 → pin 36 LP 4 → pin 17 LP 5 → pin 35 LP 6 → pin 16 LP 7 → pin 34 |
LASER extension connector L0 → pin 1 L1 → pin 3 L2 → pin 5 L3 → pin 7 L4 → pin 9 L5 → pin 11 L6 → pin 13 L7 → pin 15 / pin 17, for jumper settings see RTC manual. |
Q-Switch / laser frequency |
37-pin connector LaserA → pin 13 |
9-pin SUB-D laser connector (VB3) Laser1 → pin 1 |
LaserGate |
37-pin connector Laser_Gate → pin 31 |
9-pin SUB-D laser connector (VB3) LaserOn → pin 2 |
IO |
37-pin connector OPTO_IN 0 → pin 1 OPTO_IN 1 → pin 20 OPTO_IN 2 → pin 2 OPTO_IN 3 → pin 21 OPTO_IN 4 → pin 8 OPTO_IN 5 → pin 9
OPTO_OUT 0 → pin 3 OPTO_OUT 1 → pin 22 OPTO_OUT 2 → pin 4 OPTO_OUT 3 → pin 23 OPTO_OUT 4 → pin 27 OPTO_OUT 5 → pin 28 |
40-pin extension DIGITAL IN0 ... DIGITAL IN15
DIGITAL OUT0 ... DIGITAL OUT15
Use the SCAPS Marking Active and not RTC busyout for the job process. |
Ext. Trigger |
37-pin connector |
9-pin SUB-D laser connector (VB3) |
Start |
OPTO_IN 0 → pin 1 |
/START → pin 8 |
Stop |
OPTO_IN 1 → pin 20 |
/STOP → pin 9 |
Marking in progress |
OPTO_OUT 0 → Pin 3 |
Definable in SAMLight > Settings > System > I/O > Status Outputs |
Port |
RTC5 / RTC6 |
|---|---|
Analog A |
15-pin SUB-D laser connector Analog OUT1 → pin 8 |
Analog B |
15-pin SUB-D laser connector Analog OUT2 → pin 15 |
8 Bit Output |
EXTENSION 2 connector L0 → pin 1 L1 → pin 3 L2 → pin 5 L3 → pin 7 L4 → pin 9 L5 → pin 11 L6 → pin 13 L7 → pin 15 / pin 17, for jumper settings see RTC manual. |
Q-Switch / laser frequency |
15-pin SUB-D laser connector Laser1 → pin 1 |
Laser_Gate |
15-pin SUB-D laser connector Laser_On → pin 2 |
IO |
40-pin extension DIGITAL IN0 ... DIGITAL IN15
DIGITAL OUT0 ... DIGITAL OUT15
Use the SCAPS Marking Active and not RTC busyout for the job process. |
Ext. Trigger |
15-pin SUB-D laser connector |
Start |
/START → pin 3 |
Stop |
/STOP → pin 11 |
Marking in progress |
Definable in SAMLight > Settings > System > I/O > Status Outputs |