<< Click to Display Table of Contents > Outputs |
Laser_Gate, Laser_A, Laser_B (Laser Signals) |
|
---|---|
Supply voltage |
5.0 V (default: internally powered) |
Default polarity |
Active low |
Max. output current |
25 mA each, 70 mA in total |
Output voltage |
4.9 V @ circuit closed, no load 3.5 V @ circuit closed, max. output current |
Rise time |
< 10 ns |
Fall time |
< 10 ns |
Min. frequency |
0.19 Hz |
Max. frequency |
4 MHz |
Table 3: Laser_Gate, Laser_A, Laser_B
Laser_Port (8 bit digital) |
|
---|---|
Default polarity |
Active high |
Max. output current |
25 mA each, 75 mA in total |
Output voltage |
5.0 V @ circuit closed, no load 3.5 V @ circuit closed, max. output current |
Rise time |
< 5 ns |
Fall time |
< 5 ns |
Table 4: Laser_Port
DAC_A, DAC_B (12 bit analog out) |
|
---|---|
Max. output current |
15 mA |
Max. output voltage |
2.5 V |
5.0 V |
|
10.0 V |
|
Max. frequency |
800 kHz |
Table 5: DAC_A, DAC_B
Type |
Open-collector with internal 4k7 pull-up resistor |
Supply voltage |
5.0 V to 24.0 V (default: not powered) |
Position of load |
Chosen Opto_Out in respect to Opto_GND |
Default polarity |
Active low (low = logic circuit open) |
@ 5 V Opto_VCC supply: |
|
Max. output current |
0.33 mA each |
Output voltage |
5.0 V @ no load 3.5 V @ max. output current 0.6 V @ circuit open |
Rise time |
< 3 µs |
Fall time |
< 150 ns |
@ 24 V Opto_VCC supply: |
|
Max. output current |
1.53 mA each |
Output voltage |
24.0 V @ no load 16.8 V @ max. output current 0.7 V @ circuit open |
Rise time |
< 2 µs |
Fall time |
< 140 ns |
Table 6: Opto_Out logic circuit
Type |
Open-collector with internal 4k7 pull-up resistor |
Supply voltage |
5.0 V to 24.0 V (default: not powered) |
Position of load |
Opto_VCC in respect to the chosen Opto_Out |
Default polarity |
Active low (low = relay circuit closed) |
@ 5 V Opto_VCC supply: |
|
Max. sink current: |
35 mA each |
Load voltage |
4.4 V @ no load 4.2 V @ max. output current |
@ 24 V Opto_VCC supply: |
|
Max. sink current: |
35 mA each |
Load voltage |
23.3 V @ no load 23.2 V @ max. output current |
Table 7: Opto_Out relay circuit
Digi_Out |
|
---|---|
Default polarity |
Active high |
Max. output current |
25 mA each, 75 mA in total |
Output voltage |
5.0 V @ no load 3.5 V @ max. output current |
Rise time |
< 5 ns |
Fall time |
< 5 ns |
Table 8: Digi_Out
5V Output (pin37, pin 38) on Extension Connector |
|
---|---|
Max. output current |
150 mA in total |
Output voltage |
5.0 V |
Table 9: 5V Output on Extension Connector
Stepper_Out |
|
---|---|
Default polarity |
Active high |
Max. output current |
25 mA each, 75 mA in total |
Output voltage |
5.0 V @ no load 3.5 V @ max. output current |
Rise time |
< 5 ns |
Fall time |
< 5 ns |
Table 10: Stepper_Out
RS-232_Out |
|
---|---|
Output voltage |
+- 5.6 V @ no load |
Rise time |
< 500 ns |
Fall time |
< 650 ns |
Table 11: RS-232_out
Scanner outputs (each head for XY2-100 and XY-SCAPS interface) |
|
---|---|
Output voltage |
5.0 V @ no load |
Rise time |
< 20 ns |
Fall time |
< 20 ns |
Table 12: Scanner outputs
FA, MIP, OP (LED indicator pins) |
|
---|---|
Default polarity |
Active high |
Max. output current |
6.9 mA |
Output voltage |
3.2 V @ no load 2.2 V @ max. output current |
Rise time |
< 20 ns |
Fall time |
< 20 ns |
Table 13: FA, MIP, OP