Analog A

37-pin connector

DAC_A → pin 10

9-pin SUB-D laser connector (VB3)

Analog OUT1 → pin 4, only available if jumper is set accordingly, see RTC3 installation manual

9-pin SUB-D laser connector (VB3)

Analog OUT1 → pin 4, only available if jumper is set accordingly, see RTC4 installation manual

Analog B

37-pin connector

DAC_B → pin 29

9-pin SUB-D laser connector (VB3)

Analog OUT2 → pin 2, only available if jumper is set accordingly, see RTC3 installation manual

9-pin SUB-D laser connector (VB3)

Analog OUT2 → pin 2, only available if jumper is set accordingly, see RTC4 installation manual

8 Bit Output

37-pin connector

LP 0 → pin 19

LP 1 → pin 37

LP 2 → pin 18

LP 3 → pin 36

LP 4 → pin 17

LP 5 → pin 35

LP 6 → pin 16

LP 7 → pin 34

LASER extension connector

L0 → pin  1

L1 → pin  3

L2 → pin  5

L3 → pin  7

L4 → pin  9

L5 → pin 11

L6 → pin 13

L7 → pin 15 / pin 17 only if jumper is set accordingly, see RTC3 installation manual

LASER extension connector

L0 → pin  1

L1 → pin  3

L2 → pin  5

L3 → pin  7

L4 → pin  9

L5 → pin 11

L6 → pin 13

L7 → pin 15 / pin 17 only if jumper is set accordingly, see RTC4 installation manual

Q-Switch / laser frequency

37-pin connector

LaserA → pin 13

9-pin SUB-D laser connector (VB3)

Laser1 → pin 1

9-pin SUB-D laser connector (VB3)

Laser1 → pin 1

LaserGate

37-pin connector

Laser_Gate → pin 31

9-pin SUB-D laser connector (VB3)

LaserOn → pin 2

9-pin SUB-D laser connector (VB3)

LaserOn → pin 2

IO

37-pin connector

OPTO_IN 0 → pin  1

OPTO_IN 1 → pin 20

OPTO_IN 2 → pin  2

OPTO_IN 3 → pin 21

OPTO_IN 4 → pin  8

OPTO_IN 5 → pin  9

OPTO_OUT 0 → pin  3

OPTO_OUT 1 → pin 22

OPTO_OUT 2 → pin  4

OPTO_OUT 3 → pin 23

OPTO_OUT 4 → pin 27

OPTO_OUT 5 → pin 28

RTC3 I/O Extension Board,

68-pin SCSI Connector

DIGITAL_IN0 ...

DIGITAL_IN11,

oDIGITAL_IN12+- ...

oDIGITAL_IN15+-

DIGITAL_OUT0 ...

DIGITAL_OUT15

For proper I/O handling, use the SCAPS Marking Active signal instead of the RTC busyout signal.

40-pin extension

DIGITAL IN0 ...

DIGITAL IN15

DIGITAL OUT0 ...

DIGITAL OUT15

For proper I/O handling, use the SCAPS Marking Active signal instead of the RTC busyout signal.

Ext. Trigger

37-pin connector

9-pin SUB-D laser connector (VB3)

9-pin SUB-D laser connector (VB3)

Start

OPTO_IN 0 → pin 1

/START → pin 8

/START → pin 8

Stop

OPTO_IN 1 → pin 20

/STOP → pin 9

/STOP → pin 9

Marking in progress

OPTO_OUT 0 → Pin 3

Analog A

15-pin SUB-D laser connector

Analog OUT1 → pin 8

9-pin SUB-D laser connector

Analog OUT1 → pin 4, only available if jumper is set accordingly, see RTC SCANalone installation manual

Analog B

15-pin SUB-D laser connector

Analog OUT2 → pin 15

9-pin SUB-D laser connector

Analog OUT2 → pin 2, only available if jumper is set accordingly, see RTC SCANalone installation manual

8 Bit Output

EXTENSION 2 connector

L0 → pin  1

L1 → pin  3

L2 → pin  5

L3 → pin  7

L4 → pin  9

L5 → pin 11

L6 → pin 13

L7 → pin 15 / pin 17 only if jumper is set accordingly, see RTC5 installation manual

LASER extension SUB-D connector

L0 → pin 1

L1 → pin 2

L2 → pin 3

L3 → pin 4

L4 → pin 5

L5 → pin 6

L6 → pin 7

L7 → pin 8 / pin 9 only if jumper is set accordingly, see RTC SCANalone installation manual

Q-Switch / laser frequency

15-pin SUB-D laser connector

Laser1 → pin 1

Laser_Gate

15-pin SUB-D laser connector

Laser_On → pin 2

IO

40-pin extension

DIGITAL IN0 ...

DIGITAL IN15

DIGITAL OUT0 ...

DIGITAL OUT15

For proper I/O handling, use the SCAPS Marking Active signal instead of the RTC busyout signal.

37-pin extension1-SUB-D connector

DIGITAL IN0 ...

DIGITAL IN15

DIGITAL OUT0 ...

DIGITAL OUT15

For proper I/O handling, use the SCAPS Marking Active signal instead of the RTC busyout signal.

Ext. Trigger

15-pin SUB-D laser connector

9-pin SUB-D laser connector

Start

/START → pin 3

/START → pin 8

Stop

/STOP → pin 11

/STOP → pin 9

Marking in progress